Suzuki SX4: Anti-Theft Feature - Instrument Panel - Suzuki SX4 Owners ManualSuzuki SX4: Anti-Theft Feature

Anti-Theft Feature (1) Power on/off knob (2) Track up button/Fast forward button (3) Preset buttons (1 to 6)

The anti-theft feature is intended to discourage theft or the audio system by preventing the system from operating when it is moved to a different vehicle.

This feature works by allowing you to enter a Personal Identification Number (PIN).

When the audio system is disconnected from its power source, such as when the audio system is removed or the battery is disconnected, the system will not operate again unless the PIN is reentered.

Setting the Anti-Theft Function

1) Turn off the power by pressing the power on/off knob (1).

2) Press the power on/off knob (1) while

2) Press the power on/off knob (1) while pressing and holding the track up button (2). The ENTRY 0000 will blink and the audio system enter PIN-input mode.

NOTE:

Establish your PIN by combining numbers from 1 to 6 into any 4-digit number. If you forget your PIN, when you remove the battery for repair etc., you will no longer be able to operate the audio system.

3) Input the four digit PIN using preset buttons

3) Input the four digit PIN using preset buttons 1 to 6.

4) After you enter your four digit PIN, the

4) After you enter your four digit PIN, the display will return to 0000.

5) Input the same 4-digit number you previously

5) Input the same 4-digit number you previously entered.

6) The power of the audio system will turn

6) The power of the audio system will turn off.

NOTE:

Write down your PIN for the future use.

Canceling Your Established PIN Setting

This operation is to be done when you want to cancel the anti-theft function or change your PIN.

1) Turn off the power by pressing the power on/off knob (1).

2) Press the power on/off knob (1) while

2) Press the power on/off knob (1) while pressing and holding the track up button (2). The DELETE 0000 will blink and the audio system will enter the cancel mode.

3) Input your PIN. The power of the audio

3) Input your PIN. The power of the audio system will turn off and your PIN will be deleted.

To change your PIN, first delete your current PIN, then set a new one.

Confirming Your Personal Identification Number (PIN)

When the main power source is disconnected such as when you exchange your battery, etc, you will have to confirm your PIN to be able to use the audio system.

To confirm your PIN:

1) Turn the ignition switch to the ACC

1) Turn the ignition switch to the ACC position.

2) Input your PIN.

2) Input your PIN.

If the PIN that you input matches the registered PIN, the power of the audio system will turn off, and you will be able to operate the audio system.

NOTE:

If you input your PIN incorrectly, ---- will be displayed and the anti-theft function lock mode is entered. If you enter an incorrect PIN fewer than 6 times, the locking time will be for 15 seconds; if you enter an incorrect PIN more than 6 times, the locking time will be for 15 minutes.

If you forget your PIN and enter a wrong PIN, you can not perform any further operation.

    Remote Audio Controls (if equipped)
    Remote Audio Controls (if equipped) You can control basic functions of the audio system with the switches on the steering wheel. To control the volume: To increase the volume, push the up ...

    Troubleshooting
    Applicable to every device Radio CD Error display This unit has a number of self-diagnostic functions to protect the system. If a problem should occur, the display shows the type of error ...

    See also:

    Safety Certification
    This CD player is made and tested to meet exacting safety standards. It meets FCC requirements and complies with safety performance standards of the U.S. Department of Health and Human Services. ...

    Vehicle Identification Number (VIN)
    This legal identifier is in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside. The VIN also appears on the Vehicle Certification and ...

    Installing top tether strap
    First, secure the child restraint with the LATCH lower anchors (rear outboard seat positions only) or the seat belt, as applicable. 1. Flip up the anchor cover 1 from the anchor point which i ...